智能粮食水分测试仪的研制

给出以AT89C52单片机为核心的粮食水分测试仪的硬件结构组成,并详细介绍了信号处理和测量方法;通过对传感器的标定并进行相应的数据处理。通过实验发现,该仪器使用方便,测量精度高。     

二冲程醇类混合燃料发动机点火提前角调节系统的研究

通过分析点火提前角对发动机性能的影响,得出使用醇类混合燃料的二冲程发动机需要改进点火系统的结论。将现阶段汽车工业在点火系统上采用的微机控制点火技术加以改进后移植到二冲程发动机上,在原点火系统中加装点火控制单元ECU并将其改造成电控点火系统。改进后的点火系统可对点火提前角进行标定,对发动机在不同转速和工况下的点火提前角进行实时调节,找到发动机在该转速和工况下的理想点火提前角。改进后的二冲程汽油机可进一步改善发动机的动力性、经济性以及排放性能。     

聚合物基/稻壳粉复合材料的表面改性研究

使用JC2000A型接触角测量仪测试并研究了蒸馏水和甘油两种液体在稻壳粉填充聚乙烯(PE)、聚丙烯(PP)、聚氯乙烯(PVC)复合材料表面的接触角.研究表明:通过酸碱处理可明显改变接触角及其随时间变化的规律;其中效果最好的是以水作为探测液时,经酸处理后的PE/稻壳粉复合材料.通过方差分析得知表面改性处理方式对接触角有相当显著的影响.     

内循环(IC)厌氧反应器设计计算方法的探讨

文章论述了内循环(IC)厌氧反应器的设计计算方法,在对IC反应器水力特性分析的基础上,对有人提出计算升流管内液体升流速度的关系式进行了修正,并提供了有用的设计计算参数,最后,详细地提供了设计计算实例.     

Experimental Study on a Prestressed Frame of Two Spans Under Unsymmetric Load

By the experimental study on a full-dimensioned prestressed frame of two spans, the relative factors are analyzed such as relative height of equivalent compression zone in critical section, secondary moment, ratio of beam rigidity to column and development of cracks in the top of columns etc., which influence the moment distribution of the post-tensioned prestressed concrete frame from the side of internal force redistribution. It is believed that that the factors of relative height of concrete equivalent compression zone and secondary moment influence the moment modulation in most degree, and ratio of column rigidity to beam also plays a part in the moment modulation to some extent. Second, the plastic joints of frame with excessive spans exit in the span which endure the whole load, at last the whole frame is destroyed because of the destruction of the loading frame, the influence to the non-loading span is little.     

Maximizing Deviation Method on Comprehensive Evaluation of Commercial Bank''s Internal Control

This paper analyzes the questions that are likely to exist in comprehensive evaluation of commercial bank's internal control.On the basis of the analysis,the valuation indexes are divided into two levels.And maximizing deviation method,is introduced to get a evaluation method that can evaluate commercial bank's internal control more impersonally and more impartially.     

EDM Generating Technology of Quenched Internal Gear

Based on the infroduction of the present process of quenched internal gear, a new technolgy of machining quenched internal gear-EDM generating technology is presented with its principle and machining processes. .     

Friction and Wear Characteristics of Plastic Alloy Bearings under Different Lubricating Condition

Ultra High Molecular Weight Polyethylene (UHMW-PE) is a kind of high anti-wear engineering plastic with many excellent physical and mechanical performances. It has been widely applied in the field of mechanism such as bearing and pump. Effect of load, speed, time on friction and wear properties of Ultra High Molecular Weight Polyethylene(UHMW-PE)plastic alloy bearings under different Lubricating Condition are studied by using MPV-200 model friction and wear testing machine. The test results show that water lubrication reduces the friction coefficient of bearings but increases the wear rate as compared with dry friction. At the same time, wear mechanisms are analyzed systemically. It provides a theoretic basic for practical application of plastic alloy bearings     

Study on Dynamical Characteristic of Epicyclic Gear Drive with Internal Tooth

The epicyclic gear drive with internal tooth is analysed,a dynamic analysis model which is based on the compatibility conditions of deformation is set up.On the basis of this model,the analysis of dynamics and kinematics is made,and the influence of design parameters on dynamical characteristic is also studied.